Water Jacketed Incubator ADJW 501 Key Benefits for Consistent Laboratory Incubation

Water Jacketed Incubator ADJW 501 Key Benefits for Consistent Laboratory Incubation

Advalab Blog

Water Jacketed Incubator ADJW 501 Key Benefits for Consistent Laboratory Incubation

Blog List


Cultures grow on temperature, and temperature drifts when the room does. This article explains how a water jacketed incubator works and what to check before choosing one.

LaboratoriesHospitalsResearch CentersAdvanced Labs
46 Lchamber volume
2 to 65 °Ctemperature range
0.1 °Ctemperature resolution
40 kgnet weight

A culture left in a warm room overnight does not stay at one temperature. The door opens, the heating cycles, the room cools after hours, and a cell line or a bacterial plate feels each swing. Growth then varies from one run to the next, and nobody can say why.

The question is how to give samples a steadier temperature. The Advalab ADJW-501 publishes its chamber volume, temperature range, resolution, fluctuation, power and footprint, so a team can judge the fit before ordering.

A water jacketed incubator suits a laboratory only when those figures match its cultures and its bench. This article explains how it works, what it is used for, how a typical run goes and which mistakes to avoid, and then the next step: confirm the open points with the supplier and review the full specifications.

Incubator Principle and Uses: How the Water Jacket Works

The incubator principle and uses begin with one idea: water holds heat well. In this design, a heater warms the water in a jacket that surrounds the inner chamber, and a thermostat regulates the temperature. The water acts as a thermal buffer, so the chamber changes more slowly than the room around it.

The ADJW-501 lists a temperature range of two to sixty-five degrees Celsius, a resolution of zero point one degree and a fluctuation of plus or minus zero point two degrees. The FAQ states that distilled water is preferred in the jacket to prevent scaling, so the incubator water matters as much as the heater.

Fillthe jacket holds water around the chamber
Heata heater warms the jacket water
Bufferthe water steadies the chamber temperature
Monitorthe LCD shows temperature and time
Water jacketInner chamberAdjustable shelvesHeaterLCD control panelwater around the chambercultures and sampleswarms the watertemperature and time

Illustrative cross-section, not to scale: a heater warms the water jacket, which surrounds the inner chamber and buffers its temperature.

Where Incubation Loses Consistency

Uneven growth usually begins at a few points:

  • Room swings: heating and cooling cycles reach the chamber.
  • Door openings: temperature drops each time the door opens.
  • Coarse readouts: a display with wide steps hides small drift.
  • Hot spots: uneven heat treats samples differently by shelf.
  • Unclear limits: nobody knows which conditions the unit is rated for.

A Water Jacketed Incubator lab setup addresses these points with a thermal buffer, a fine readout and stated stability figures.

What the Published Features Add to Incubation

Each benefit below ties to a specification or feature published for the ADJW-501.

Forty-Six-Liter Chamber

The listing gives a chamber volume of forty-six liters.

Wide Temperature Range

The range runs from two to sixty-five degrees Celsius.

Fine Resolution

Temperature resolution is zero point one degree Celsius.

Low Fluctuation

Temperature fluctuation is listed as plus or minus zero point two degrees Celsius.

Adjustable Shelves

Shelves can be arranged for flexible space management.

LCD Screen

The screen shows temperature and time.

Low-Noise Fan

The page metadata describes a low-noise fan for uniform temperature distribution.

Steel Shell

The shell is cold-rolled steel with a spray plastic coating.

Stated Power Draw

Power consumption is four hundred thirty watts.

Compact Footprint

The housing measures four hundred sixty by five hundred ten by seven hundred sixty-five millimeters.

Published figures for the ADJW-50146 Lchambervolume2 to 65 °Ctemperaturerange0.1 °Ctemperatureresolution± 0.2 °Ctemperaturefluctuation430 Wpowerconsumption2 / 4shelvesas listed220 V50 Hz powersupply as listed

Infographic: capacity, temperature, shelf and power figures from the ADJW-501 listing.

Water Jacketed Incubator Uses in Cell Culture and Microbiology

Water jacketed incubator uses, as named by Advalab, cover two areas. The listing describes these settings for water jacketed incubator equipment:

  • Cell culture: growing and maintaining mammalian cells, stem cells or hybridomas in research laboratories.
  • Microbiology: cultivating bacteria and fungi in clinical and medical research laboratories.
  • Routine research: the incubators category names microbiology, cell culture, quality testing and routine tasks.

Many readers search for a water jacketed CO2 incubator or a water jacket CO2 incubator. The ADJW-501 listing gives no carbon dioxide or oxygen specification, so confirm gas control with the supplier if your work needs it, or compare the air jacketed CO2 incubator range and the biological CO2 incubator range. Questions about CO2 incubator water usually concern humidity, and the listing gives no humidity range, so ask the supplier how moisture should be handled.

A Typical Incubation Routine

The listing does not publish an operating procedure, so follow the supplier manual for exact steps. A Water Jacketed Incubator use routine follows a short sequence:

Fill the jacketFill the water jacket as the manual directs, using distilled water as the FAQ prefers.
Place the unitSet it on a level bench with room around it, and connect the power supply.
Set the temperatureChoose the value for your cultures within the listed range of two to sixty-five degrees Celsius.
Let it stabilizeAllow the chamber to reach the set value before loading samples.
Load the shelvesArrange cultures on the shelves with space for even heat.
Check and recordRead the LCD and note the temperature and time at each check.

What to Check Before You Choose

Match these published figures against your own cultures and bench before shortlisting an incubator with a water jacket:

Forty-six literschamber volume
Two to sixty-five degrees Celsiustemperature range
Zero point one degree Celsiustemperature resolution
Plus or minus zero point two degrees Celsiustemperature fluctuation
Four hundred thirty wattspower consumption
Three hundred ten by three hundred eighty by four hundred fifty millimetersinternal size
Interior46 L310×380×450Internal size (W × D × H)310 × 380 × 450 mmHousing size (W × D × H)460 × 510 × 765 mmPackage size (W × D × H)580 × 620 × 910 mm40 kg net, 48 kg gross

Infographic: interior and floor-planning figures published for the ADJW-501.

  • Confirm the temperature range, since the FAQ gives five to sixty degrees Celsius while the specifications give two to sixty-five.
  • Ask whether the unit ships with two or four shelves, since the listing says "2/4 pc".
  • Confirm the power option, since the table lists two hundred twenty volts at fifty hertz while the inquiry form offers other supplies.
  • Ask for the jacket water capacity, humidity range and any gas control, which are not published.

Common Selection Mistakes

Choosing by volume aloneCheck the interior height and shelf count against your vessels, not only the liter figure.
Overlooking jacket waterPlan for clean, distilled water and a routine check of the jacket.
Skipping the power checkConfirm voltage and frequency before ordering.
Ignoring the wider rangeIf your work needs another format, review the other types in the incubators range before deciding.

Comparing Models in the Water Jacketed Range

ModelChamber volumeTemperature rangeResolution
ADJW-501Forty-six litersTwo to sixty-five degrees CelsiusZero point one degree Celsius
ADJW-502Seventy litersTwo to sixty-five degrees CelsiusZero point one degree Celsius
ADJW-503One hundred sixty litersTwo to sixty-five degrees CelsiusZero point one degree Celsius
ADJW-504Two hundred forty-seven litersTwo to sixty-five degrees CelsiusZero point one degree Celsius

Where a Water Jacketed Incubator Sits in the Incubator Category

The incubators category at Advalab spans compact benchtop formats and high-capacity floor models for microbiology, cell culture, quality testing and routine research. Besides the water jacketed incubator range, it lists the constant temperature incubator range, the air jacketed and biological CO2 incubators, cooling incubators and microplate incubators, among others.

When laboratories compare options in this category, they typically weigh chamber volume, temperature range and fluctuation, heating method, shelving, gas control and footprint. To review all formats side by side, explore the full incubators range, or see the wider laboratory equipment catalog on the Advalab home page.

Why the ADJW-501 May Suit Your Laboratory

The Water Jacketed Incubator ADJW-501 pairs a 46-liter chamber, a range of 2 to 65 degrees Celsius, a resolution of zero point one degree and a stated fluctuation of plus or minus zero point two degrees in a compact bench unit. It suits research and clinical laboratories that grow cell cultures or microbial samples in small batches.



Hazel Daniels

Specialty: Healthcare Technology & Laboratory Equipment

Writing Style: Professional, informative, and reader-friendly

Bio: Hazel Daniels specializes in writing about healthcare technology, laboratory equipment, and scientific applications. She presents technical information in simple language, highlighting practical uses and industry developments.

www.linkedin.com/in/hazel-daniels-4a108b444

See the Full Specifications

Review the published volume, temperature, power and size details for this water jacketed incubator and compare them against your own cultures and bench.

Explore Water Jacketed Incubator ADJW-501